Expert Answers about Toyota Bike Accessories

• Installation of the Lets Go Aero Anti-Rattle Trailer Hitch Receiver Lock
• The SilentACT Anti-Rattle Trailer Hitch Lock - 1-1/4" and 2" Hitches # SHP2082 is designed to be used with a ball mount or other accessory. The bike racks normally have a brand specific anti-rattle locking hitch where the inside of the bike rack shank that goes into your receiver is not hollow and rather is already threaded for that brand pin so you wouldn't need a separate one for another vehicle as most fit 1-1/4 and 2 inch hitches. There are a few bike racks that do not have a threaded...
  view full answer...


• Using Stabilization Strap # 18050 On Curt Trailer Hitch Receivers Using Accessories
• When using the Curt Trailer Hitches like # C11441, Curt requires a stabilization strap # 18050 to support any load that is non-trailer like a bike rack or cargo carrier. You will find this note in the installation details attached. I've linked a video to the stabilization strap as well as the videos we have made for that product. This strap will attach to your vehicle and to the accessory, not to the hitch. This will stabilize the accessory by adding another point of contact so that...
  view full answer...


• Are Any Additional Products Needed to Install Curt Trailer Hitch # 13354 on 2008 Acura MDX
• The Curt Trailer Hitch # 13354 that you referenced comes with all the necessary hardware to install on your 2008 Acura MDX, so you will not need any additional accessories to complete the installation. A hitch lock is not a necessity for the hitch installation; however, I highly recommend using a lock with both your bikes and bike rack. The Trailer Hitch Receiver Lock # C23519 is an economical way to safeguard your investment. Another option is the Hollywood Racks # HRLHPC2 which is a...
  view full answer...


• What is the Purpose of the Stabilizer Strap That is to be Used On CURT Class I Hitches
• The strap you are referring to is the Curt Bike Rack Strap # 18050. It helps provide extra security to hitch mounted bike racks when using hitch mounted accessories. The strap provides additional support to the rack and would help prevent additional wear on the hitch and your vehicle when using hitch mounted accessories such as a bike rack. The hitch is stable, but the strap will more offer more stability, and failure to use a strap will void the warranty of the hitch. I attached installation...
  view full answer...


• Why Cant the Kuat NV 2.0 Base 4-Bike Platform Rack be Used on a Trailer
• The reason that the Kuat NV 2.0 Base 4-Bike Platform Rack part # BA22B-BA02B cannot be used on the back of a trailer is because the manufacturer says not to. The reason they say not to is because of the pivot point this rack has. The amount of movement that a hitch mounted accessory on the back of a trailer is going to be faced with is far more than that of a hitch mounted accessory on the back of a vehicle. The reason for the has to due with the increased distance from the rear axle. This...
  view full answer...


• Where Does a Trailer Hitch Install on a 2003 Honda S2000
• The Curt trailer hitch # C11212 attaches to the frame of the 2003 Honda S2000 in 2 places and to the trunk pan in 4 places. I have linked the installation instructions that show this. This is the only hitch available for your S2000. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch. Curt also...
  view full answer...


• Does Bumper Fascia have to be Cut or Trimmed to Install Trailer Hitch on a 2014 Nissan Versa
• You will have to trim the heat shield to install Curt trailer hitch # C11256 on your 2014 Nissan Versa, but not the bumper. I have included a link to the installation instructions for you that show where to trim the heat shield. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch. For a bike...
  view full answer...


• Is Bumper/Fascia Trimming Required to Install a Trailer Hitch on a 2007 Honda Element SC
• The Curt Class I hitch # C11699 does not require trimming anything for installation. I have linked the instructions for this hitch for you to view. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch. Curt also says you have to use stabilization strap # 18050 when using this hitch for any non-trailer...
  view full answer...


• Can the Gen-Y Rebel Ball Mount w/ Stacked Receiver Be Used for Towing and Bike Rack
• Yes, the Gen-Y Rebel Ball Mount w/ Stacked Receivers like part # GY72FR can be used for towing and hitch mounted accessories at the same time. The hitch accessory will need to be installed in the upper receiver and then you can use either of the bottom two receivers for the ball mount.
  view full answer...


• Where Does Curt Trailer Hitch Bolt Onto on a 2017 Chevy Spark
• We haven't had the chance to install Curt trailer hitch # C11433 on a 2017 Chevy Spark so there aren't pictures. But I have included a picture from the installation instructions linked here and on the product page for the hitch that shows the bolt locations on the vehicle. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2...
  view full answer...


• Is Drilling Required to Install Curt Trailer Hitch C11312 on a 2005 Ford Mustang
• For Curt trailer hitch # C11312 for your 2005 Ford Mustang you might have to enlarge an access hole which you could do with a drill. But no new holes will need to be drilled. And you may not have to enlarge the access hole either. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch. Curt also...
  view full answer...


• Does Car have to be Jacked Up to Install a Trailer Hitch on a 2007 Saab 9-3
• You would not have to jack up your 2007 Saab 9-3 to install Curt trailer hitch # C11326. But it will make it a whole lot easier if you did. I have included a link to the installation instructions and a video showing an example install for you. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch. Curt...
  view full answer...


• Can MaxxTow MT70066 Ball Mount/Receiver Flat Tow a Vehicle and Carry Bike Rack at the Same Time
• If both the trailer ball and the receiver portion of the # MT70066 is used at the same time, the 500 lb tongue weight capacity of the # MT70066 won't be reduced. Flat towing a vehicle doesn't apply any tongue weight to the ball mount/receiver so as long as the weight of the bike rack and the bikes don't exceed the 500 lb tongue capacity of the ball mount/receiver or the tongue weight capacity of the hitch (whichever is lower), this ball mount will work great for you for carrying the bike...
  view full answer...


• Ball Mount With 2 Inch Accessory Receiver Operation
• The Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs, # D210 will allow you to use your 90 degree bike rack and your trailer. I've attached a video of the review of this hitch with a bike rack installed. You can see from the clearance on the video that you won't have enough clearance to safely connect your trailer with the bike rack in place without risking hitting your bike rack. You will need to first connect the trailer and then load the...
  view full answer...


• Installation Instructions for Draw-Tite Trailer Hitch 24796 and a 2015 Nissan Altima
• There is a bulkhead underneath the 2015 Nissan Altima that will serve as a guide to line the hitch, # 24796, up properly. Once the hitch is in place you will use it as a template to drill the holes needed for installation. I have included a link to the installation instructions and a video showing an example installation for you. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer...
  view full answer...


• How Hard is it to Install a Trailer Hitch on a 2014 Kia Rio
• Take a look at the video I have linked showing installation of Draw-Tite hitch # 24884 on a vehicle. The vehicle in the video shares the same frame as your 2014 Kia Rio. So all things being equal the installation in the video will be basically identical on your car. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum...
  view full answer...


• Trailer Hitch Installation on a 2013 Chevy Volt
• I have always liked the Chevy Volt. I like the tail lights and look of the rear end. We have not had the chance yet to install Curt trailer hitch # C11221 on a 2013 Chevy Volt. But if you are near Wentzville, Missouri we would love to have the vehicle in to do some test fits! I have included a link to the installation instructions for you though. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use...
  view full answer...


• Where Does the Fascia have to be Trimmed on a 2016 Audi A4 to Install a Trailer Hitch
• Yes, fascia trimming is required to install Draw-Tite trailer hitch # DT24950 on a 2016 Audi A4. The area that needs to be trimmed is up underneath the vehicle and not visible otherwise. I have included a diagram that shows the area that needs to be trimmed. This is a bottom view as if you were lying on the ground looking up at the bottom of the vehicle. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated...
  view full answer...


• How Much Crossbar Spread Is Needed For Kayak Carrier And Bike Carriers On Camper Shell Roof Rack
• The crossbar spread will vary depending on the accessory you want to put on the roof rack. The Yakima FrontLoader Wheel Mount Bike Carrier, part # Y02103 will work with a crossbar spread between 16 and 48 inches, so you can see it will work with most roof racks. Most kayak carriers, like part # TH834 require at least 24 inches crossbar spread. I recommend making sure you have at least the 24 inches for a spread but I would probably place them about 28 inches apart. Again, I recommend...
  view full answer...


• How to Install a Trailer Hitch for a 2013 Smart fortwo
• The bumper does not have to be removed to install Curt trailer hitch # C11020 on your 2013 Smart fortwo. I have included a link to the installation instructions for the hitch so you can see all of the steps. I have also linked a video showing installation for you. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum...
  view full answer...